Solar Panel Mounting Options (17)

Renusol Console+ bucket for flat roof or ground mount Max module length: 1550-2150 mm#1: REN-520075-K#2: ***COMPLETE KIT WITH FIXINGS*** Renusol Console+ 5200 75 K Minimum order - 5 Renusol Console+ bucket - minimum order of 4 units unless order together with any other products Available for delivery only Renusol Console+ 5200 75 K The ConSole+ provides an angle of 15 degrees.The ConSole+ assembly system is the ideal solution for installing PV modules on flat roofs with a pitch of up to 5 degrees without roof penetration. Most commercially available framed standard PV modules fit the ConSole+.The ConSole+ is weighed down with ballast e.g. gravel, paving slabs, etc... in order to resist the windloads. The necessary weight of the ballast depends on the height of the building, its location and the condition of the ground and the wind and snow loads. Reference values for the necessary ballasts are contained in "Preparing the Assembly - Point 2" in the table of Page 5 of the installation manual.Details:- Colour: black- Suitable for flat-roof- and ground mounting installations- For framed PV-modulesTechnical Data:- Material: HDPE, Aluminium and stainless steel- Max module length: 1550-2150 mm- Holes gap - width: 895-1014 mm- Holes gap - length: 690-1180 mmOther Contents:- 1 x 500075 ConSole+- 2 x 400005 ConSole U-Profile 1035 mm- 4 x 900027 Hexag# screw DIN933-M6x20 A2-70- 4 x 900028 Washer DIN9021-6,4-A2- 4 x 900029 Self-locking hexag# nut DIN985-M6-A2- 4 x 900106 ConSole Clip- 4 x 900115 Hexag# screw DIN7504-ST5,5x25-A2-SW8

Emlite 1-ph Bi-Directional generation meter 100A (1000 pulse/kWh)#1: EM-ECA2-BI Meters - Single Phase BiDirectional Generation Meters  Emlite 1ph Installer Notes  Emlite 1ph Certification  Emlite 1ph Warranty Emlite Single Phase Bi-Directional (Import/Export) Total Generation Meter 100A with Pulse Output Emlite Bi-Directional meter provides three different readings that scroll across on the screen automatically; these readings are Import, Export and NET values.    NET Values should be used as Feed In Tariff readings when used with DC coupled storage or Hybrid (PV and Battery) inverters.  This meter meets the “Bi-directional meter” criteria as listed in ‘Guidance for generators: Co-location of electricity storage facilities with renewable generation supported under the Renewables Obligation or Feed-in Tariff schemes (Version 2)’  document released by OFGEM.

Emlite 3-ph generation meter EMP.az, 100A (1000 pulse/kWh) #1: EMP1-AZ  Emlite 3-ph Data Sheet  Emlite 3ph User Manual  Emlite 3-ph Certification  Part of the Emlite three phase metering range which offers superb meters for a wide range of applications where basic metering is needed. They are of high quality and sturdy construction with features normally found in more expensive meters. Product Features Accuracy Class A and B 4 quadrant energy measurement Optional power quality information Configurable pulsed outputs Clear and easy to read LCD display Solid Brass terminals Optional finger guard for main terminals

Bird Deterrent 30m Solar Panel Bird Exclusion Kit (Galvanized Mesh) #1:BIRD-MESH Accessories - Bird Protection Use this kit to prevent pigeons and other birds seeking shelter and roosting underneath solar panels. Enviroguard Bird Mesh is more permanent and safer than nylon pigeon netting in which birds can get trapped when it degrades. The initial outlay is balanced out by lower maintenance costs as it's easier to remove and refit during routine inspections.   30 Meter Galvanised Solar Panel Weld Mesh Roll 60 Solar Panel Mesh Clips 1 Standard Wire Cutter 1 Pack Stainless Steel Corner Ties

MC4 Basic Crimping pliers 2.5/4/6mm2 #1:MC4-CRIMP-TOOL  Crimping pliers for private use PV-CZM-BS   Suitable for the assembly of products approved by TÜV in small amounts. Simple crimping tool without locator and without spare parts (not possible to replace the inserts) Crimp cycles : 30’000 cycles guaranteed   Complete tool for the assembly of the original MC4.     part code 32.6025 PV-CZM-BS   PLEASE NOTE THIS TOOL IS NOT SUITABLE FOR MC4-Evo2 CONNECTORS. ITS FOR STANDARD MC4 ONLY.

4mm2 single-core DC solar cable 50m - Black #1:CABLE4-1-50 Cables - DC Cables 4 mm², single-core, black, 50m NEW H1Z2Z2-K certified 50m solar cable with length label.  Manufactured against the latest European Standard EN 50618 and with the harmonised designation H1Z2Z2-K, these Solar DC Cable are specified cables for use in Photovoltaic (PV) systems, and in particular those for installation at Direct Current (DC) side with a nominal DC voltage of up to 1.5kV between conductors as well as between conductor and earth, and not exceeding 1800V. EN 50618 requires cables to be low smoke zero halogen and be flexible tin-coated copper conductors with a single core and cross-linked insulation and sheath. Cables are required to be tested at a voltage of 11kV AC 50Hz and have an operating temperature range of -40oC to +90oC. H1Z2Z2-K supersedes the previous TÜV approved PV1-F cable. H1Z2Z2-K PHOTOVOLTAIC CABLE CONSTRUCTION Conductor          Flexible tinned copper (Class 5) Insulation           Halogen-free cross-linked compound Outersheath      Halogen-free cross-linked flame retardant compound   The compounds used in these solar cable's insulation and outersheath are halogen free cross-linked, hence the reference to these cables as "cross-linked solar power cables". The EN50618 standard sheathing has a thicker wall than the PV1-F cable version.

6mm2 single-core DC solar cable 50m - Black #1:CABLE6-1-50 Cables - DC Cables APPLICATION -Updated harmonised (H1Z2Z2-K) European standard solar cable intended for the interconnection within photovoltaic systems such as solar panel arrays. -Suitable for fixed installations, internal and external, within conduit or systems, but not direct burial applications. -Our solar cable is ozone-resistant according to BS EN 50396, UV resistant according to HD 605/A1, and is tested for durability according to EN 60216.   

4mm2 single-core DC cable 100m - Black #1: CABLE4-1-100  4 mm², single-core, black, 100m NEW H1Z2Z2-K certified 100m solar cable with length label.  Manufactured against the latest European Standard EN 50618 and with the harmonised designation H1Z2Z2-K, these Solar DC Cable are specified cables for use in Photovoltaic (PV) systems, and in particular those for installation at Direct Current (DC) side with a nominal DC voltage of up to 1.5kV between conductors as well as between conductor and earth, and not exceeding 1800V. EN 50618 requires cables to be low smoke zero halogen and be flexible tin-coated copper conductors with a single core and cross-linked insulation and sheath. Cables are required to be tested at a voltage of 11kV AC 50Hz and have an operating temperature range of -40°C to +90°C. H1Z2Z2-K supersedes the previous TÜV approved PV1-F cable. H1Z2Z2-K PHOTOVOLTAIC CABLE CONSTRUCTION Conductor          Flexible tinned copper (Class 5) Insulation           Halogen-free cross-linked compound Outersheath      Halogen-free cross-linked flame retardant compound   The compounds used in these solar cable's insulation and outersheath are halogen free cross-linked, hence the reference to these cables as "cross-linked solar power cables". The EN50618 standard sheathing has a thicker wall than the PV1-F cable version. As with the TÜV PV1-F cable, the EN50618 cable benefits from a double-insulation offering increased safety. The Low Smoke Zero Halogen (LSZH) insulation and sheathing makes them suitable for use in environments where corrosive smoke would present a risk to human life in the event of fire.

6mm2 single-core DC solar cable 50m - Black #1: CABLE6-1-100 Cables - DC Cables   6 mm single-core, black, 100m 100m solar cable with length label Manufactured against the latest European Standard EN 50618 and with the harmonised designation H1Z2Z2-K, these Solar DC Cable are specified cables for use in Photovoltaic (PV) systems, and in particular those for installation at Direct Current (DC) side with a nominal DC voltage of up to�1.5kV�between conductors as well as between conductor and earth, and not exceeding�1800V.�EN 50618 requires cables to be low smoke zero halogen and be flexible tin-coated copper conductors with a single core and cross-linked insulation and sheath. Cables are required to be tested at a voltage of 11kV AC 50Hz and have an operating temperature range of -40oC to +90oC. H1Z2Z2-K supersedes the previous T�V approved PV1-F cable.  

10mm2 single-core DC solar cable 100m - Black #1: CABLE10-1-100   100m solar cable with length label. Supplied on a reusable spool. Conductor cross-section: 10 mm² (this is not the cable diameter, but rather the cross-sectional area).  System voltage: 1800 V Rated current: 70 A according to DIN VDE 0298 part 4 Operating temperature range: -40 - 120 °C Solar cable, high temperature and UV-resistant, reliable for inside and outside use. Resistant to ammonia, ozone, mineral oil and acid. Excellent fire-resistance. Colour: Black

4mm2 single-core DC cable 250m - Black #1: CABLE4-1-250   4 mm², single-core, black, 250m NEW H1Z2Z2-K certified 250m solar cable with length label.  Manufactured against the latest European Standard EN 50618 and with the harmonised designation H1Z2Z2-K, these Solar DC Cable are specified cables for use in Photovoltaic (PV) systems, and in particular those for installation at Direct Current (DC) side with a nominal DC voltage of up to 1.5kV between conductors as well as between conductor and earth, and not exceeding 1800V. EN 50618 requires cables to be low smoke zero halogen and be flexible tin-coated copper conductors with a single core and cross-linked insulation and sheath. Cables are required to be tested at a voltage of 11kV AC 50Hz and have an operating temperature range of -40°C to +90°C. H1Z2Z2-K supersedes the previous TÜV approved PV1-F cable. H1Z2Z2-K PHOTOVOLTAIC CABLE CONSTRUCTION Conductor          Flexible tinned copper (Class 5) Insulation           Halogen-free cross-linked compound Outersheath Halogen-free cross-linked flame retardant compound       The compounds used in these solar cable's insulation and outersheath are halogen free cross-linked, hence the reference to these cables as "cross-linked solar power cables". The EN50618 standard sheathing has a thicker wall than the PV1-F cable version. As with the TÜV PV1-F cable, the EN50618 cable benefits from a double-insulation offering increased safety. The Low Smoke Zero Halogen (LSZH) insulation and sheathing makes them suitable for use in environments where corrosive smoke would present a risk to human life in the event of fire.

6mm2 single-core DC solar cable 50m - Black #1:CABLE6-1-250  Cables - DC Cables   250m solar cable with length label. Manufactured against the latest European Standard EN 50618 and with the harmonised designation H1Z2Z2-K, these Solar DC Cable are specified cables for use in Photovoltaic (PV) systems, and in particular those for installation at Direct Current (DC) side with a nominal DC voltage of up to 1.5kV between conductors as well as between conductor and earth, and not exceeding 1800V. EN 50618 requires cables to be low smoke zero halogen and be flexible tin-coated copper conductors with a single core and cross-linked insulation and sheath. Cables are required to be tested at a voltage of 11kV AC 50Hz and have an operating temperature range of -40oC to +90oC. H1Z2Z2-K supersedes the previous TÜV approved PV1-F cable.H1Z2Z2-K PHOTOVOLTAIC CABLE CONSTRUCTIONConductor Flexible tinned copper (Class 5)Insulation Halogen-free cross-linked compoundOutersheath Halogen-free cross-linked flame retardant compound The compounds used in these solar cable's insulation and outersheath are halogen free cross-linked, hence the reference to these cables as "cross-linked solar power cables". The EN50618 standard sheathing has a thicker wall than the PV1-F cable version.  

4mm2 single-core DC cable 500m - Black #1: CABLE4-1-500   4 mm², single-core, black, 500m NEW H1Z2Z2-K certified 500m solar cable with length label. Supplied on a reusable spool. Manufactured against the latest European Standard EN 50618 and with the harmonised designation H1Z2Z2-K, these Solar DC Cable are specified cables for use in Photovoltaic (PV) systems, and in particular those for installation at Direct Current (DC) side with a nominal DC voltage of up to 1.5kV between conductors as well as between conductor and earth, and not exceeding 1800V. EN 50618 requires cables to be low smoke zero halogen and be flexible tin-coated copper conductors with a single core and cross-linked insulation and sheath. Cables are required to be tested at a voltage of 11kV AC 50Hz and have an operating temperature range of -40oC to +90oC. H1Z2Z2-K supersedes the previous TÜV approved PV1-F cable. H1Z2Z2-K PHOTOVOLTAIC CABLE CONSTRUCTION Conductor          Flexible tinned copper (Class 5) Insulation           Halogen-free cross-linked compound Outersheath      Halogen-free cross-linked flame retardant compound   The compounds used in these solar cable's insulation and outersheath are halogen free cross-linked, hence the reference to these cables as "cross-linked solar power cables". The EN50618 standard sheathing has a thicker wall than the PV1-F cable version. As with the TÜV PV1-F cable, the EN50618 cable benefits from a double-insulation offering increased safety. The Low Smoke Zero Halogen (LSZH) insulation and sheathing makes them suitable for use in environments where corrosive smoke would present a risk to human life in the event of fire.

6mm2 single-core DC solar cable 50m - Black #1:CABLE6-1-500  Cables - DC Cables 6 mm², single-core, black, 500m 500m solar cable with length label. Supplied on a reusable spool. Conductor cross-section: 6 mm²  (this is not the cable diameter, but rather the cross-sectional area).  System voltage: 1800 V Rated current: 70 A according to DIN VDE 0298 part 4 Operating temperature range: -40 - 120 °C Solar cable, high temperature and UV-resistant, reliable for inside and outside use. Resistant to ammonia, ozone, mineral oil and acid. Excellent fire-resistance. Colour: Black It's important to choose the correct cable spec for your project. We can provide assistance with this if needed.

4mm2 single-core DC cable 1000m - Black #1: CABLE4-1-1000   4 mm², single-core, black, 1000m 1000m solar cable with length label. Supplied on a reusable spool. Conductor cross-section: 4 mm² (this is not the cable diameter, but rather the cross-sectional area).  System voltage: 1800 V Rated current: 70 A according to DIN VDE 0298 part 4 Operating temperature range: -40 - 120 °C Solar cable, high temperature and UV-resistant, reliable for inside and outside use. Resistant to ammonia, ozone, mineral oil and acid. Excellent fire-resistance. Colour: Black

6mm2 single-core DC solar cable 50m - Black #1:CABLE6-1-1000  Cables - DC Cables 6 mm², single-core, black, 1000m 500m solar cable with length label. Supplied on a reusable spool. Conductor cross-section: 6 mm²  (this is not the cable diameter, but rather the cross-sectional area).  System voltage: 1800 V Rated current: 70 A according to DIN VDE 0298 part 4 Operating temperature range: -40 - 120 °C Solar cable, high temperature and UV-resistant, reliable for inside and outside use. Resistant to ammonia, ozone, mineral oil and acid. Excellent fire-resistance. Colour: Black It's important to choose the correct cable spec for your project. We can provide assistance with this if needed.